Whisper In The Wind Designs : CT PTU TUT for S&CO- The Night Fury tube by Danny Lee, and the Night Fury kit match by Designs By Joan!

Friday, May 16, 2014

CT PTU TUT for S&CO- The Night Fury tube by Danny Lee, and the Night Fury kit match by Designs By Joan!

9:44 AM | Posted by Unknown | Edit Post

Preview of the Night Fury tube by Danny Lee!

Preview of the Night Fury kit match by Designs By Joan!

Preview of Mask #23, by me!

Snag Tag #1

Snag Tag #2

Snag Tag #3

Snag Tag #4

CT PTU TUT for the Night Fury tube by Danny Lee, and the Night Fury scrap kit by Designs By Joan!

Materials Needed

The Night Fury tube by Danny Lee, which can be purchased at S&CO HERE

The Night Fury scrap kit by Designs By Joan, which can be purchased at S&CO HERE

Mask #23, created by me, which can be downloaded HERE

PSP - I am using X5, but any should do

**This tutorial assumes that you have a working knowledge of basic functions in PSP. This tutorial is a creation of my own, and any similarities are purely coincidental. If you make something with one of my tuts or templates, please email it to me at robynebutts@gmail.com and I will post it her on my blog!

Okay, let's begin! Let's create our mask layer! Open whatever mask you chose, I chose a mask I created. Now create a new image 800x800, with a transparent back. Now for this mask, I used a paper instead of flood-filling; so open paper 1, and copy and paste it to the new image. Now, go to the top layers menu and click NEW MASK LAYER>FROM IMAGE..a pop up opens...click on the title of the mask you chose in the drop-down menu. Merge visible layers, then copy and paste it to the tag. Re-size and move as needed...for this one I increased the size by 5%, then centered it.

Now, open el 44, leaving the size as is, place it on the bottom right..D and FH, and place on bottom left...D and move back..go to the right one and D and move back.

Open el 65, leaving the size as is, place it centered at the bottom.

Open el, 54, reduce 25%, place on left, behind the gate.

Open el 46, reduce 35%, place on the right side, front of the house layer.

Open the full-view of the tube, reduce 30%, center on tag, front of the gate.

Open the close-up of the tube, place top right on mask, reduce to fit, invert, add screen blend mode.

Open el 10, reduce 60%, place bottom left, front of gate.

Open el 1, reduce 35%, place bottom left, front of el 10. .

Open el 33, reduce 60%, place bottom left in front of gate...D, FH and place on right side.

Open el 69, leaving the size as is..FH and place top left corner.

Open el 41, reduce 40%, place bottom right, front of gate.

Open el 47, reduce 30%, place bottom right, front of el 41.

Open el 57, reduce 60%, place bottom right, left of candle.

Open el 12, leaving the size as is, place centered on mask layer.

Open el 26, leaving the size as is, place top left by tree..D and FH and place top right by the close up.

Open el 19, reduce 60%, place bottom left, by trunk.

Open el 43, reduce 80%, place bottom left, front of el 19.

Open el 9, reduce 65%, place angled bottom right, behind the book.

Open el 21, reduce 80%, place bottom right, front of book.

Open el 37, leaving the size as is, place top right on mask layer below the close-up, D and reduce 60%, place top left...D and move over to the right a bit.

Open el 77, leaving the size as is, place on house layer.

Open el 23, reduce 10%, place bottom left on gate post.

Open el 60, reduce 60%, place angled top left.

Open el 64, leaving the size as is, place at the bottom, in front of flames.

Open el 32, reduce 40%, place bottom left by the dog.

Open el 34, reduce 80%, place bottom right corner, behind book.

Open el 12, reduce 70%, place bottom right on gate post..D and FH and place on the left side.

Lastly, add 3D drop shadows on whatever elements you would like them on. I like these settings: 2V 1H 70 op, 4B. Make sure at this point that you add copyright info for the tube artist..you can also add info for the scrap maker if the tube maker's TOU allows. Make sure you check TOU's!

You did it! You have completed this tut! Now you can add personalization to your creation! I hope you enjoyed this tutorial; if you did, please follow my blog, and pass it on to others! Also, please email your creations with my tuts or templates, and I will happily display them here on my blog (robynebutts@gmail.com)!

Hugz and Blessings,

Robyne'